First Boot
If all went as planned, your first boot should look something like this.
 +-----------------------------------------+
| |
| | ______
| | | ____| __ ___ ___
| Welcome to FreeBSD! | | |__ | '__/ _ \/ _ \
| | | __|| | | __/ __/
| | | | | | | | |
| 1. Boot FreeBSD [default] | |_| |_| \___|\___|
| 2. Boot FreeBSD with ACPI enabled | ____ _____ _____
| 3. Boot FreeBSD in Safe Mode | | _ \ / ____| __ \
| 4. Boot FreeBSD in single user mode | | |_) | (___ | | | |
| 5. Boot FreeBSD with verbose logging | | _ < \___ \| | | |
| 6. Escape to loader prompt | | |_) |____) | |__| |
| 7. Boot FreeBSD with USB keyboard | | | | |
| 8. Reboot | |____/|_____/|_____/
| |
| |
| |
| Select option, [Enter] for default |
| or [Space] to pause timer 6 |
+-----------------------------------------+

Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 6.0-RELEASE #0: Thu Nov 3 09:36:13 UTC 2005
root@x64.samsco.home:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Geode(TM) Integrated Processor by National Semi (266.65-MHz 586-class CPU)
Origin = "Geode by NSC" Id = 0x540 Stepping = 0
Features=0x808131<FPU,TSC,MSR,CX8,CMOV,MMX>
real memory = 134217728 (128 MB)
avail memory = 121913344 (116 MB)
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
cpu0 on motherboard
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
sis0: <NatSemi DP8381[56] 10/100BaseTX>
port 0xe100-0xe1ff mem 0xa0000000-0xa0000fff irq 10 at device 6.0 on pci0
sis0: Silicon Revision: DP83816A
miibus0: <MII bus> on sis0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis0: Ethernet address: 00:00:24:c1:ca:20
sis1: <NatSemi DP8381[56] 10/100BaseTX>
port 0xe200-0xe2ff mem 0xa0001000-0xa0001fff irq 10 at device 7.0 on pci0
sis1: Silicon Revision: DP83816A
miibus1: <MII bus> on sis1
ukphy1: <Generic IEEE 802.3u media interface> on miibus1
ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis1: Ethernet address: 00:00:24:c1:ca:21
sis2: <NatSemi DP8381[56] 10/100BaseTX>
port 0xe300-0xe3ff mem 0xa0002000-0xa0002fff irq 10 at device 8.0 on pci0
sis2: Silicon Revision: DP83816A
miibus2: <MII bus> on sis2
ukphy2: <Generic IEEE 802.3u media interface> on miibus2
ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis2: Ethernet address: 00:00:24:c1:ca:22
isab0: <PCI-ISA bridge> port 0x6100-0x613f,0x6200-0x623f at device 18.0 on pci0
isa0: <ISA bus> on isab0
pci0: <bridge> at device 18.1 (no driver attached)
atapci0: <National Geode SC1100 ATA33 controller>
port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xe000-0xe00f at device 18.2 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
pci0: <bridge> at device 18.5 (no driver attached)
ohci0: <OHCI (generic) USB controller>
mem 0xa0003000-0xa0003fff irq 11 at device 19.0 on pci0
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: (0x0e11) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xc8000-0xd0fff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: unable to get the current command byte value.
ppc0: parallel port not found.
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
Timecounters tick every 1.000 msec
ad0: 30MB <SanDisk SDCFB-32 Vdg 1.25> at ata0-master PIO4
Trying to mount root from ufs:/dev/ad0a
Loading configuration files.
No suitable dump device was found.
Entropy harvesting: interrupts ethernet point_to_point kickstart.
Starting file system checks:
/dev/ad0a: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0a: clean, 14136 free (432 frags, 1713 blocks, 1.5% fragmentation)
Setting hostname: workbox.ultradesic.build.
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mstu 16384
i inet6 ::1 prefisxlen 128
0 inet6 fe80::1%l:o0 prefixlen 64 scopeid 0x4
ilnet 127.0.0.1 neitmask 0xff000000n
sis0: flags=8k843<UP,BROADCAST ,RUNNING,SIMPLEXs,MULTICAST> mtu t1500
options=8a<VLAN_MTU>
inett6 fe80::200:24fef:fec1:ca20%sis0 prefixlen 64 tecntative scopeid h0x1
inet 192.a168.1.4 netmask n0xffffff00 broadgcast 192.168.1.2e55
ether 00:00d:24:c1:ca:20
to UP
media: Ethernet autoselect (10baseT/UTP)
status: active
Generating nsswitch.conf.
Generating host.conf.
add net default: gateway 192.168.1.1
Additional routing options:.
Mounting NFS file systems:.
Creating and/or trimming log files:.
Starting syslogd.
/etc/rc: WARNING: Dump device does not exist. Savecore not run.
ELF ldconfig path: /lib /usr/lib
a.out ldconfig path: /usr/lib/aout
Starting local daemons:.
Starting sshd.
Initial i386 initialization:.
Additional ABI support:.
Starting cron.
Local package initialization:.
Additional TCP options:.
Starting background file system checks in 60 seconds.

Fri Dec 16 14:53:09 EST 2005

FreeBSD/i386 (workbox.ultradesic.build) (ttyd0)

login: